JCB 540-170 LOAD CONTROL (SUPPLEMENT) Service Repair Manual

16 pages
0 views
of 16

Please download to get full document.

View again

All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Share
Description
Service Manual Load Control (Supplement) K Introduction ( T 1) K LCS (Six Valve Manifold) ( T 9) K LC1 and LC4 (540-170 Only) ( T 37) K LC2 and LC3 ( T 67) K LC5 ( T…
Transcript
Service Manual Load Control (Supplement) K Introduction ( T 1) K LCS (Six Valve Manifold) ( T 9) K LC1 and LC4 (540-170 Only) ( T 37) K LC2 and LC3 ( T 67) K LC5 ( T 151) K MC05 ( T 187) K MC06 ( T 217) K Fault Finding ( T 321) K Testing and Adjustment ( T 329)Publication No.9803/3665-3World Class Customer Support Copyright Š 2004 JCB SERVICE. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any other means, electronic, mechanical, photocopying or otherwise, without prior permission from JCB SERVICE. Issued by JCB Technical Publications, JCB Aftermarket Training, Woodseat, Rocester, Staffordshire, ST14 5BW, England. Tel +44 1889 591300 Fax +44 1889 591400Contents Page No. Introduction About This Supplement ................................................................................. 1 About the Load Control Systems ................................................................... 2 Identification .................................................................................................. 3 Care and Safety ............................................................................................ 7 LCS (Six Valve Manifold) Introduction .................................................................................................... 9 Circuit Description ....................................................................................... 11 Hydraulics Schematic .................................................................................. 20 Electrical Schematic .................................................................................... 22 Harness Data ............................................................................................... 24 Logic Sequence ........................................................................................... 28 Calibration ................................................................................................... 31 LC1 and LC4 (540-170 Only) Introduction .................................................................................................. 37 Circuit Description ....................................................................................... 39 Hydraulics Schematic .................................................................................. 47 Harness Data ............................................................................................... 50 Logic Sequence ........................................................................................... 54 Installation ................................................................................................... 56 Calibration ................................................................................................... 62 LC2 and LC3 Introduction .................................................................................................. 67 Circuit Description - 528-70 ......................................................................... 69 Circuit Description - 535-95, 531-70, 536-70 and 541-70 ........................... 75 Circuit Description - 533-105 and 540-140 .................................................. 86 Circuit Description - 535-125 HiViz and 535-140 HiViz ............................... 99 Hydraulics Schematic ................................................................................ 109 Harness Data ............................................................................................. 114 Logic Sequence (All LC2/LC3 Systems) ................................................... 131 Calibration ................................................................................................. 133 LC5 Introduction ................................................................................................ 151 Circuit Description ..................................................................................... 153 Hydraulics Schematic ................................................................................ 169 Harness Data ............................................................................................. 172 Logic Sequence ......................................................................................... 178 Calibration ................................................................................................. 180 MC05 Introduction ................................................................................................ 187 Circuit Description ..................................................................................... 189 Hydraulics Schematic ................................................................................ 201 Harness Data ............................................................................................. 204 Electrical Schematics ................................................................................ 209 Logic Sequence ......................................................................................... 211 Calibration ................................................................................................. 213 MC06 Introduction ................................................................................................ 217 Circuit Descriptions - Parallel Machines .................................................... 219iiContents Page No. Circuit Description - LSP + Gearpump Machines ...................................... 235 Circuit Description - LSP + Variflow Machines .......................................... 250 Hydraulics Schematics .............................................................................. 265 Harness Data ............................................................................................. 277 Electrical Schematics ................................................................................ 300 Logic Sequence ......................................................................................... 305 Calibration ................................................................................................. 307 Fault Finding All Load Control Systems .......................................................................... 321 Testing and Adjustment Testing ....................................................................................................... 329 Adjustment ................................................................................................ 340iiiiIntroduction About This Supplement Machine Model and Serial NumberUsing the Service Manual SupplementThis publication provides information for the following Load Control Systems:This manual is a supplement to the JCB Loadall Service Manual. The information covers the JCB Loadall machines fitted with the Load Control System.– LCS (Six Valve Manifold) Load Control System Each variant of Load Control System (see opposite) is dealt with separately, each having its own topic in this Supplement.– LC1/LC4 Load Control System – LC2/LC3 Load Control System – LC5 Load Control System – MC05 Load Control System – MC06 Load Control System See the appropriate system topic for machine serial nos., where relevant.Only those areas of the machine which are different from the standard Loadall are dealt with here. For all other information refer to the appropriate Loadall Service Manual. Unless specified otherwise, all references to `Service Manual' in this supplement are to be taken as meaning the Service Manual specific to the standard machine. Read the standard Service Manual and this supplement completely and carefully to familiarise yourself with the machine before carrying out any servicing procedures.Units of Measurement T1-001 2In this publication, the S.I. system of units is used. For example, liquid capacities are given in litres. The Imperial units follow in parentheses ( ) eg 28 litres (6 gal).Cross References T1-004 2In this publication, page cross references are made by presenting the subject title printed in bold, italic and underlined. It is preceeded by the 'go to' symbol. The number of the page upon which the subject begins, is indicated within the brackets. For example: K Cross References ( T 1).19803/3665-31Introduction About the Load Control SystemsAbout the Load Control Systems General Information A Load Control System (LCS) is an enhancement to the devices that JCB currently fit as standard, i.e. loadcharts, boom extension markers and Load Moment Indicator (LMI). These are still the primary source of information to allow the operator to operate the machine correctly. The Load Control System offers additional control if the operator makes an inadvertent movement of the load. The system must not be relied upon as the primary source of protection for the machine. The duty of care is still with the operator/site agent to: – know the mass and load centre of loads being handled. – know boom angle and extension that will be required to place the load (this can be checked by doing a dry run first without the load) – whilst moving the load, obey LMI indications, lift charts and boom extension markers. Note: Note: The LCS provides a degree of protection only against the machine tipping forward. It does not protect against tipping sideways or rearwards, nor tipping due to the machine being used on unsuitable ground nor operator mishandling (sharp direction changes, etc.). Neither will the system protect against instability due to the stabiliser legs being lifted nor misuse of the chassis levelling (sway) function (if either of these options are fitted).29803/3665-32Introduction IdentificationIdentification There are many variants of the Load Control System. Although they all have a common purpose - to help prevent the load moving into a position which would make the machine unstable - there are variations in the way this is achieved on different Loadall models. Also, some variants of the system incorporate additional features such as stabiliser isolation and load retrieval. The following tablewill help you identify which variant may be installed on any particular model of Loadall. Note: For 536-60, 536-70, 531-70, 535-95 and 541-70 machines, you will need also to refer to the table of Hydraulic System Variants. K Table 2. Identification of Hydraulic System Variants (536-60, 536-70, 535-95, 531-70 & 541-70) ( T 5)528-70536-60531-70536-70541-70532-120533-105535-95535-125535-125 Hi-Viz535-140535-140 Hi-Viz537-135540-140Territories540-170Table 1. System Applicability, Identifying Features and Territorial AvailabilitySystemFrancezz z zzLCSRest of the World (ROW) (not Australia/New Zealand)z z z z z z z z z z z zROW (not Australia/New Zealand)3z z z z z zz z9803/3665-3zDescription and Identifying FeaturesVisual IdentifierOriginal system (now obsolete). Identifying features: large 6-valve manifold mounted on the chassis side plate and twin aperture LMI.LC22 stage cut -out system. Identifying features: Additional switch in cab for Load Control selection. Load Control Valve inserted between pump and valve block and single aperture LMI with 4 way and 6 way connectors.LC3As LC2 + stabiliser isolation. Identifying features: as LC2, plus stabilisers isolate at 10° boom angle.3Introduction528-70536-60531-70536-70541-70532-120533-105535-95535-125535-125 Hi-Viz535-140535-140 Hi-Viz537-135540-140Territories540-170IdentificationSystemROW (not Australia/New Zealand)zz z z zLC5ROW (not Australia/New Zealand)zROW (not Australia/New Zealand)Australia/New ZealandLC1zz4zz zz z z z9803/3665-3Visual Identifier2 stage cut -out system + lift & retract to retrieve load. Identifying features: Additional switch in cab for Load Control selection. Load Control Valve inserted between pump and valve block, single aperture LMI with 4 way and 6 way connectors and switches on the valve block. 540-170 system. Identifying features: twin LMI aperture with 4 way & 6 way connectors.LC4As LC1+ stabiliser isolation. Identifying features: as LC1, plus stabilisers isolate at 10° boom angle.MCO5As LC1 + AS1418.19. Identifying features: twin aperture LMI with 4 way & 8 way connectors.MCO62 stage cut-out system + lift & retract to retrieve load + AS1418.19. Identifying features: Additional switch in cab for Load Control selection. Boom back switch, single aperture LMI with 4 way & 6 way connectors.Australia/New ZealandzDescription and Identifying Features4Introduction IdentificationHydraulic System Variants (536-60, 536-70, 535-95, 531-70 & 541-70) The hydraulic circuit of the 536-60, 536-70, 535-95, 531-70 and 541-70 machines may be one of a number of variants. Each variant requires a slightly different Load Control System. If you are working with one of these machines it is important that you know which type of hydraulic system isinstalled, to ensure that you refer to the correct hydraulic and electrical diagrams in this supplement. The following table shows the easily identifiable differences between hydraulic systems.Table 2. Identification of Hydraulic System Variants (536-60, 536-70, 535-95, 531-70 & 541-70) System Type Main Pump Type Control Lever Type Parallel System5Fixed flow double or triple gear pump.Parallel control valve (black) with four manual spools. Separate control levers for boom and auxiliary services.Fixed flow double or triple gear pump.Parallel control valve (black) with two electro servo and two manual spools. Cab mounted control lever with push button controls.Fixed flow double gear pump.Parallel control valve (black) with two integrated electro servo spools and two manual spools. Cab mounted control lever with thumbwheel controls. Hydraulic services are controlled by a machine control ECU with electronic flowshare feature.9803/3665-35Introduction Identification System Type LSP Gearpump SystemLSP Variflow System6Main Pump TypeControl Lever TypeFixed flow triple gear pump.Flowshare control valve (blue) with two proportional electro servo and two manual spools. Cab mounted control lever with thumb wheel controls.Variable flow pump with one fixed flow gearpump for cooling fan, sway and servo oil supply.Flowshare control valve (blue) with two electro servo and two manual spools. Cab mounted control lever with thumbwheel controls.Variable flow pump with one fixed flow gearpump for cooling fan, sway and servo oil supply.Flowshare control valve (blue) with four integrated electro servo spools. Seat pod mounted control lever with thumbwheel controls9803/3665-36Introduction Care and SafetyCare and Safety Safety NoticesGeneral SafetyIn this publication and on the machine, there are safety notices. Each notice starts with a signal word. The signal word meanings are given below.!MDANGER Denotes an extreme hazard exists. If proper precautions are not taken, it is highly probable that the operator (or others) could be killed or seriously injured.!MDANGER Study this Supplement and the Service Manual for the machine before carrying out any maintenance work on the machine. You must always understand and observe the relevant laws and regulations. If you are unsure about anything, ask your JCB Distributor. INT-1-2-6INT-1-2-1!MWARNING Denotes a hazard exists. If proper precautions are not taken, the operator (or others) could be killed or seriously injured. INT-1-2-2!MCAUTION Denotes a reminder of safety practices. Failure to follow these safety practices could result in injury to the operator (or others) and possible damage to the machine. INT-1-2-379803/3665-37Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITINGNOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.LCS (Six Valve Manifold) Introduction Machine Model and Serial Numberthroughout the range. The extend function operates as normal until the limit is reached.The LCS Load Control System (LCS) is compatible with following models in the JCB Loadall machine range: – 528-70 Up to SN 797511 – 532-120 Up to SN 1064455 – 533-105 Up to SN 1064702It is, therefore, a characteristic of the system that lowering and tilt movements are slightly slower than when Ground Work mode is selected. This is normal and does not indicate a machine fault. Once the limit is reached, any movement of the load which would further reduce the stability of the machine is prevented. This means that extend, lower, crowd and dump functions are all disabled.– 535-95 Up to SN 1064715 – 537-135 Up to SN1064473General Description When the LCS is selected, it reduces the risk of tipping forward when the machine reaches a predetermined point near to its maximum working limit. This is achieved by stopping boom lower, boom extend, dump and crowd functions, in order to prevent further movement of a load past the predetermined point.In Ground Work mode, the system functions as the standard LMI. Testing procedures described in this manual should be carried out on level ground with the road wheels in the straight ahead position.Boom lift and boom retract functions are allowed in order to retrieve the load from a point of cutout. The system has two working modes, Load Control Mode and Ground Work Mode. Load Control Mode is automatically entered when the machine is started. Note: The LCS provides a degree of protection only against the machine tipping forward. It does not protect against tipping sideways or rearwards, nor tipping due to the machine being used on unsuitable ground nor operator mishandling (sharp direction changes, etc.). Neither will the system protect against instability due to the stabiliser legs being lifted nor misuse of the chassis levelling (sway) function (if either of these options are fitted). The stabilisers and/or chassis levelling rams are not interlocked into the LCS. In Load Control mode, the boom lower hydraulic supply is progressively reduced (derated) as the weight on the rear axle becomes less, ensuring that the load movement is stopped smoothly and without jerking. The tilt hydraulic flow is also restricted; this restriction is constant99803/3665-39LCS (Six Valve Manifold) Introduction The LCS Indicator DisplayAGreen LEDs (3)Safe when litBAmber LEDCaution when lit approaching machine stability limitsCRed LEDDanger when lit - machine at limit of stabilityDPower ON indicatorEDisplay buttonFMode change buttonGLoad Control mode symbolLit when Load Control mode selected, flashes when red LED C is lit (in Load Control mode)HGround Work mode symbolLit when Ground Work mode selectedFig 1.109803/3665-310LCS (Six Valve Manifold) Circuit DescriptionCircuit Description IntroductionFig 2. Typical Circuit The following description, outlines the operation of the LCS as fitted to Series I machines fitted with stabilisers (532-120, 533-105 and 537-135). It should be read with reference to the following:between the main control valve block and the service rams. Refer to:K Hydraulics Schematic ( T 20)K Component Key ( T 12)K Electrical Schematic ( T 22)K Fig 2. ( T 11)K Logic Sequence ( T 28)K Fig 3. ( T 13)In non-stabilised machines (528-70, 535-95), valve C (lift circuit control valve) is not fitted and references to valve C should be ignored. The lift service operates normally.Interface with Standard Hydraulic System Load Control functions are controlled by the six valve manifold AA, which is inserted in the hydraulic circuit119803/3665-311LCS (Six Valve Manifold) Circuit Description Component KeyNote: All valves are shown in the de-energised position.K Fig 2. ( T 11) and K Fig 3. ( T 13)Note: Valve C and associated components shown thus are fitted only to machines equipped with stabilisers:AASix valve manifoldAProportional valve (PWM) regulating lower serviceBSolenoid valve controlling lower service regulationCSolenoid valve controlling lift service(1)DSolenoid valve controlling extension and tilt servicesESolenoid valve controlling tilt circuit (dump)FSolenoid valve con
Related Search
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks