Audi A8 1994-2016 & Audi R8 2006-2015 & Audi V8 1989-1994 & Audi S8 1996-2016 Workshop Repair manual

44 pages
0 views
of 44

Please download to get full document.

View again

All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Share
Description
audi :: Audi A8L Quattro Sedan V8-4.2L (AKB) ( 2002)> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Alarm Module, (Vehicle…
Transcript
audi :: Audi A8L Quattro Sedan V8-4.2L (AKB) ( 2002)> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Alarm Module, (Vehicle Antitheft) > Component Information > LocationsAlarm Module: LocationsComponent LocationsCentral Locking/alarm System/interior Light Delay Control Module V94> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Alarm Module, (Vehicle Antitheft) > Component Information > Locations > Page 7Alarm Module: Service and Repair RemovingThe control module for interior monitoring -1- is installed in the left-rear of the trunk, below the pump for the central lo - Remove left rear trunk trim panel. - Remove two nuts (arrows). - Disconnect harness connector at control module. Installing Installation is the reverse order of removal. Pin assignment of control module harness connector - Control module removedControl Module Harness Connector, Terminal Assignment 1 2 3 4 5 6 7 8 9 10 11 12 13-Voltage supply terminal 30 06.95: not occupied; 07.95 >: Ground terminal 31 Activating/deactivating CL pump Ventilation low Voltage supply sensor, left Ground sensor, left Analog signal sensor, left 40 kHz-Cycle sensor, left 06.95: not occupied; 07.95 >: switch for deactivation Output control lamp Ground terminal 31 Not occupied Input door contacts14 15 16 17 18 19 20--Ventilation highsensor, right Voltage supply Ground sensor, right Analog signal sensor, right 40 kHz-cycle sensor, right Not occupied Alarm output to CL pumpPin assignment of sensor harness connector - Sensor unit removed> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Alarm Module, (Vehicle Antitheft) > Component Information > Locations > Page 8A8L Quattro Sedan V8-4.2L (AKB) (2002)Sensor Harness Connector, Terminal Assignment 1 2 3 4-40 kHz-cycle Voltage supply Ground Analog signal> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Antenna Control Module > Component Information > Service and RepairAntenna Control Module: Service and Repair Removing - Remove rear seat backrest. - Remove lower C-pillar trim.-Remove 3 securing nuts -2-. Disconnect harness connector and remove control module.Installing - Install in reverse order of removal.> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Emergency Contact Module > Component Information > Technical Service Bulletins > Telematics(R) BatteryEmergency Contact Module: Technical Service BulletinsTelematics(R) System - Switching Off Emergency Batte 91 08 88 2002385/4 November 10, 2008. Supersedes Technical Service Bulletin Group 91 number 07-34 dated August 10, 2007 for reasons listed below.Affected Vehicles 91 Telematics system, switching off emergency batteryCondition The emergency battery needs to be switched off. Technical BackgroundVehicles with Telematics system are equipped with an emergency (back-up) battery that provides auxiliary power to thIn order to avoid unnecessary discharge of the Telematics emergency (back-up) battery, it should always be switched o Production Solution Audi Telematics by OnStar is available as an option on all A4, A6 and A8 models beginning with 03.02 production. Service Emergency Battery, switching off/on: Refer to step-by-step procedure in Repair Manual >> Communication >> Repair Group 91. Warranty This TSB is informational only and not applicable to any Audi warranty.Additional Information More information on this system can be found in the following resources: -Owners Manual: Audi Telematics by OnStar Owner's Guide-SSP: For telematics system description and function information, see Audi Telematics by OnStar Self Study Prog-VAS Scan Tool: Telematics system OBD functions for A4 models, see VAS 5051 tester in mode "Guided Fault FThe following repair procedure(s) will be necessary to complete this procedure:> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Emergency Contact Module > Component Information > Technical Service Bulletins > Telematics(R) System - Switching Off Emergency Battery > Page 16A8L Quattro Sedan V8-4.2L (AKB) (2002)-For Telematics system repair and OBD information, see Repair Manual >> Communication >> Repair Groups 01All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Pa> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Navigation Module > Component Information > Technical Service Bulletins > Navigation System - FaNavigation Module: Technical Service BulletinsNavigation System - False CAN Communication Faults 91 07 59 2016907/1 Dec. 10, 2007Vehicle Information ConditionNo customer complaint, but in the fault protocol of the Navigation 4, one or several sporadic communication faults abo Technical BackgroundWhen starting the vehicle, the battery voltage may drop so far that the communication on the data bus is briefly disrupt Production Solution No change. ServiceIgnore and erase the fault code entries if there is no customer complaint. A replacement of the navigation system is not Warranty This TSB is informational only and not applicable to any Audi warranty. Additional InformationAll parts and service references provided in this TSB are subject to change and/or removal. Always check with your Pa> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Navigation Module > Component Information > Technical Service Bulletins > Page 21Navigation Module: Locations1 2 -3 4 5 6 7-Connecting block with four multi-pin connections and a fuse20-pin multi-pin harness connector I consisting of:Yellow 6-pin partial connectorGreen 6-pin partial connecto Brown 8-pin multi-pin connector II Black 8-pin multi-pin connector III Red 10-pin multi-pin connector IV Antenna connection GPS; connecting socket for navigation antenna on trunk lid. Securing bracket for antenna connectionMulti-pin harness connectors I, II ,III, IV at rear of -J401, terminal assignment20-pin multi-pin connector I 1 2 3 -CAN-high telematic CAN-high display CAN screen telematic45 6 7 8 9 10 11 12 13 14 15 16--CAN-low CAN-low telematic display CAN screen display Button branch 2 Output A Switch Button branch 3 Output B Ground (GND) NF + NF mute navi NF Telephone NF (+)> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Navigation Module > Component Information > Technical Service Bulletins > Page 22A8L Quattro Sedan V8-4.2L (AKB) (2002)17 18 19 20-Tel-active / mute FAW Tel-NF-screen Telephone NF (-) Not assignedBrown 8-pin multi-pin connector II 1 2 3 4 5 6 7 8-Not assigned Not assigned Not assigned Not assigned Not assigned Not assigned Not assigned Not assignedBlack 8-pin multi-pin connector III 1 2 3 4 5 6 7 8-Gala (RPM signal) Reverse light switch K-diagnostic Terminal 15 Not assigned Not assigned Terminal 30 Terminal 31Red 10-pin multi-pin connector IV 1 2 3 4 5 6 7 8 9 10-Not assigned Not assigned Not assigned Not assigned Not assigned Not assigned Not assigned Not assigned Not assigned Not assigned> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Navigation Module > Component Information > Technical Service Bulletins > Page 23Navigation Module: Service and Repair The control module is located in the left storage compartment in the luggage compartment. Removing - Open left storage compartment in luggage compartment.-Unscrew the four securing screws (arrows). Disconnect the electrical harness connector and the antenna wire at the rear of the control module. Remove the control module -1-.WARNING!Never use screws other than the original screws for securing the control module, as this could destr Installing - Install in reverse order of removal.NOTE: When installing: The control module for navigation and installation frame must be installed together in horizontal position and - In addition, air circulation must be ensured, meaning that ventilation slots of the control module may not be c - When replacing the control module, make sure to send in the completed form for navigation system complain> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Parking Assist Control Module > Component Information > Service and RepairParking Assist Control Module: Service and Repair Control Module For Parking Aid -J446-, Removing and Installing Removing - Remove cover from storage compartment at left in the luggage compartment. - Remove frame for CD-changer if installed.-Remove both hex bolts -2- and remove the control module for parking aid -1- together with bracket -4-. Disconnect electrical harness connectors. Control module for parking aid -1- is secured to bracket -4- with two Phillips-head screws -3-.Installing - Install in reverse order of removal.> Relays and Modules > Relays and Modules - Accessories and Optional Equipment > Remote Control Module, Audio - Stereo > Component Information > Service and RepairRemote Control Module: Service and Repair Removing: - Remove driver's side storage compartmentControl module for multi-function steering wheel -J453- is stored in a double relay housing and is located in relay so -Remove control module for multi-function steering wheel from relay socket.Installing: - Install in reverse order of removal.> Relays and Modules > Relays and Modules - Body and Frame > Head Restraint Relay > Component Information > Locations > Relay to Lower Headrest, Rear, Left -J376-Head Restraint Relay: LocationsRelay to Lower Headrest, Rear, Left -J376-Component LocationsRelay To Lower Headrest, Rear, Left/Right J376, J377> Relays and Modules > Relays and Modules - Body and Frame > Head Restraint Relay > Component Information > Locations > Relay to Lower Headrest, Rear, Left -J376- > Page 35Head Restraint Relay: LocationsRelay to Lower Headrest, Rear Right -J377-Component LocationsRelay To Lower Headrest, Rear, Left/Right J376, J377> Relays and Modules > Relays and Modules - Body and Frame > Power Door Lock Control Module > Component Information > Service and RepairPower Door Lock Control Module: Service and RepairThe control module for heated door locks is located at the upper door cross member in the driver's door. - Remove door trim panel. See: Body and Frame/Doors, Hood and Trunk/Doors/Front Door/Front Door Panel/Serv-Remove both screws. Disconnect electrical connector and remove control module> Relays and Modules > Relays and Modules - Body and Frame > Power Seat Control Module > Component Information > LocationsPower Seat Control Module: LocationsComponent LocationsMemory Seat Control Module J136> Relays and Modules > Relays and Modules - Body and Frame > Power Seat Control Module > Component Information > Locations > Page 42Power Seat Control Module: Service and Repair Control Module For Seat Adjustment With Memory, Removing And Installing -Front and rear seat height adjuster in highest position Seat removed-Remove nuts (arrows) several rotations. Remove control module for seat adjustment with memory from bracket. Remove connector. NOTE: Colors of connector are stamped into connector fields of control module.> Relays and Modules > Relays and Modules - Body and Frame > Power Seat Relay > Component Information > Locations > Power Seat Power Supply Relay, J137Power Seat Relay: LocationsPower Seat Power Supply Relay, J137Component LocationsPower Seat Power Supply Relay J137> Relays and Modules > Relays and Modules - Body and Frame > Power Seat Relay > Component Information > Locations > Power Seat Power Supply Relay, J137 > Page 47Power Seat Relay: LocationsRelay for Adjustable Passenger Seat, J409 Auxiliary fuse and Relay Panel E-Box, footwell front right> Relays and Modules > Relays and Modules - Body and Frame > Power Seat Relay > Component Information > Locations > Page 48Power Seat Relay: Service and Repair Current Supply Relay For Seat Adjustment, Removing And Installing -Seat removedRemoving-Remove 4 phillips-head screws (arrows) for retaining plate. Fold retaining plate forward. Remove connector.-Remove Phillips-head screw (arrow) and remove current supply relay for seat.Installing - 4.5 Nm (40 in.lb.)Secure relay with to retaining plate.> Relays and Modules > Relays and Modules - Body and Frame > Sunroof / Moonroof Module > Component Information > LocationsSunroof / Moonroof Module: LocationsComponent LocationsPower Sunroof Control Module J245> Relays and Modules > Relays and Modules - Brakes and Traction Control > Brake Fluid Pump Relay > Component Information > LocationsBrake Fluid Pump Relay: Locations Fuse & Relay Arrangement on the Relay Panels Micro Central Electric Panel, In E-Box, Footwell Front Right1 2 4 -Dual Horn Relay, J4 Load Reduction Relay, J59 Fuel Pump (FP) Relay, J17Relay and Fuse Panel, Electronic Box Plenum Chamber2b 4 -Fuse for Control Module - Automatic Transmission, S113 Secondary Air Injection (AIR) Pump Relay, J299
Related Search
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks